INTSHAYELELO YOKUGQIBELA KWI-SHORT SPKS, iitanki ezigqithisileyo kunye noomatshini bokupelwa kwe-peen
Le tanki yokudubula iqulathe ikakhulu i-bit yetanki, i-hopper, ibhokisi ye-valve, ivalve yomoya, ivalve yoomoya, ivali yokutsala, ivali ye-bill {1}.
Emva kokuba i-ebrasive igcwaliswe kwitanki etyhidiweyo kunye nengcinezelo ngaphakathi kwe-pipe isungulwe i-valve ye-tirk kunye ne-ransing {0}, ikhutshiwe kwaye ikhutshwe ngesantya esingama-60 Iimitha kwisibini . i-hopper isetiwe encotsheni ye-shoen tank . itanki letanki isetyenziselwe ukubamba i-abrasves . Inxalenye ephezulu ixhotywe ngevalve yezinto zexabiso (kunye nenqanaba lezinto ezibonakalayo), indawo engezantsi yetanki iqhagamshelwe kwi-valve ye-faceling . ivalve yetanki rod . xa ukunyuka kwamaxabiso kwenziwa kwitanki, i-cone inyuka inyuka ivali yokutywina kwetanki. I-valve, ikhutshiwe . ngokuhlengahlengisa isifo se-veen valve, ireyithi yokuhamba kwe-abraring iguqulwe kwaye ifumane isiphumo esihle sokuxhuzula .
Iitanki ezitywiniweyo ze-peen, iitanki ezingapheliyo kunye nokubethwa kwesanti zenziwe ngetekhnoloji yelinye ilizwe kwaye zineempawu ezilandelayo:
Itanki yokuTyhila, itanki elingapheliyo kunye ne-Planeng Peen Lin linokufikelela kumsebenzi "wokudubula ngokuzenzekelayo xa i-birrator yamkelwe" Ukusebenza . amandla ejet anamandla kwaye azinzile {{4} .}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}} {i-{8}} ulawulo .
Oomatshini bokugcina amanzi asimahla, iitanki zesanti zamanzi kunye neetanki zesanti yolwelo ziintlobo zokuqala zesanti {{1} .
Iitanki zokutsala, iitanki ezigqithisileyo, i-shot sutes emanzi kunye neetanki zentlabathi ezimanzi zilungele
1. ukucocwa kwesanti yentsalela, isikali se-oxide kunye namanye amasuntswana kumphezulu wokuphosa emva kokungafundiswanga;
2.} Susa i-rumps ukusuka kumphezulu weeprofayili kunye nemibhobho yentsimbi, kunye nokulinganisa kwe-oxide kwimiphezulu yeendawo zokuzilawula, amacandelo e-Weldied kunye ne-Deadpieces kunye ne-Deadpieces kunye ne-Deadpieces kunye ne-Deadpieces kunye ne-DeadPieces kunye ne-DeadPies.
3. njengesongezelelo kumtshini wokudubula, unokusetyenziselwa ukugcwalisa iikona ezifileyo kunye neenqwelwana zangaphakathi ezintsonkothileyo zicociwe ngokutsala.
Iiparamitha zobugcisa zezinto eziphezulu zokuhombisa
|
Umxholo |
Iyunithi |
St 70-} dx -2 d |
St 70- lx -2 d |
|
|
1 |
Ivolumu yetanki ye-Pieen |
m3 |
0.67 |
0.67 |
|
2 |
Ububanzi bendlela yomoya oxinzelelweyo |
″ |
1 1/2 |
1 1/2 |
|
3 |
Uxinzelelo lomoya |
Mpa |
0.5-0.6 |
0.5-0.6 |
|
4 |
I-Spray Ivora (i-Diameter φ10mm) |
Kg / h |
1800-2200 |
3600-4400 |
|
5 |
Ukusetyenziswa komoya |
M3 / min |
6.1 |
6.1*2 |
|
6 |
Ubude bombhobho odubulayo |
mm * 2 |
7000 |
7000 |
|
7 |
Imilinganiselo yangaphandle |
mm |
1120*900*1690 |
1120*900*2190 |
|
8 |
Indlela yokusebenza |
Ithutyana |
Iyaqhubeka |
